1995 Ford F700 Recall | The Hand Throttle Cable Can Wear The Brass Swivel Block On The Governor Lever Through Which It Passes.

1995 Ford F700 Vehicle Speed Control Recall | Aug 02, 1995

The Hand Throttle Cable Can Wear The Brass Swivel Block On The Governor Lever Through Which It Passes.this Wear Can Result In The Governor Jamming In Thedamaged Swivel And Could Prevent The Governor Lever From Returning To The Idle Position.. Follwoing Is The Summary Of Corrective Actions Taken: Dealers Will Install A Revised Governor Lever With A Stainless Steel Swivel. Also Letters Will Be Sent To Vehicle Owners That Have The Same Vehicles But Do Not Have A Ford Installed Hand Throttle Advising Them That They May Require Service If They Have Had An After Market Hand Throttle Installed.
system: Fuel; Throttle Linkages And Control.vehicle Description: Trucks, Chassis-cabs And Cowl-chassis Vehicles With Inline Fuel Injection Pump Equipped Fd-1060 Or Fd-1460 Engines And Hand Throttles.note: The Vehicle Brakes Are Capable Of Overriding The Engine Power And Bringing The Vehicle To A Stop.note: Owners Who Take Their Vehicles To An Authorized Dealer On An Agreed Upon Service Date And Do Not Receive The Free Remedy Within A Reasonablet Ime, Should Contact Ford At 1-800-392-3673. Also Contact The National Highway Traffic Safety Administration’s Auto Safety Hotline At 1-800-424-9393.

This recall was issued on Aug 02, 1995 for 1995 Ford F700, manufactured by FORD MOTOR COMPANY, in response to Vehicle Speed Control problems.

1995 Ford Explorer Recall | The Hydraulic Lift Cylinders Are Attached To Brackets That Are Welded To The Liftgate. The Bracket Welds Can Fracture.

1995 Ford Explorer Structure,body,hatchback/liftgate,support Device Recall | Aug 25, 1995

The Hydraulic Lift Cylinders Are Attached To Brackets That Are Welded To The Liftgate. The Bracket Welds Can Fracture.with A Broken Bracket Weld, There Is A Potential For The Liftgate Bracket To Gradually Bend Inward Allowing The Lift Cylinderball Stud To Disengage.. Follwoing Is The Summary Of Corrective Actions Taken: Dealers Will Install Reinforcement Brackets.
system: Structure; Hatchback Hydraulic Cylinder.vehicle Description: Multi-purpose Passenger Vehicles.note: Owners Who Take Their Vehicles To An Authorized Dealer On An Agreed Upon Service Date And Do Not Receive The Free Remedy Within A Reasonable Time, Should Contact Ford At 1-800-392-3673. Also Contact The National Highway Traffic Safety Administration’s Auto Safety Hotline At 1-800-424-9393.

This recall was issued on Aug 25, 1995 for 1995 Ford Explorer, manufactured by FORD MOTOR COMPANY, in response to Structure,body,hatchback/liftgate,support Device problems.

1995 Ford Explorer Recall | The Passenger Side Air Bag Has An Inflator Body That Cracked During Forming Of The Curl That Retains The Igniter Plug In The End Of The Inflator. Also The Igniter End Cap Can Separate

1995 Ford Explorer Air Bags,frontal Recall | Feb 24, 1995

The Passenger Side Air Bag Has An Inflator Body That Cracked During Forming Of The Curl That Retains The Igniter Plug In The End Of The Inflator. Also The Igniter End Cap Can Separate From The Inflator.the Passenger Side Air Bag May Not Inflate Properly Resulting In Reduced Occupant Protection In A Vehicle Accident. If The Igniter End Cap Separates In A Frontal Collision, Hot Gases Can Be Released And Ignite Flammable Material Or Cause Burn Injuries.. Follwoing Is The Summary Of Corrective Actions Taken: Dealers Will Remove And Replace The Passenger Side Air Bag Module.
system: Interior; Passive Restraints; Air Bag; Passenger. Vehicle Description: Passenger Side Air Bag In Passenger Cars, Vans Andmulti-purpose Vehicles. Note: If Your Vehicle Is Presented To An Authorized Dealer On An Agreed Upon Service Date And The Remedy Is Not Provided Free Of Charge Within A Reasonable Time, Contact Ford At 1-800-392-3673. Also Contact The National Highway Traffic Safety Administration’s Auto Safety Hotline At 1-800-424-9393.

This recall was issued on Feb 24, 1995 for 1995 Ford Explorer, manufactured by FORD MOTOR COMPANY, in response to Air Bags,frontal problems.

1995 Ford Probe Recall | The Passenger Side Air Bag Has An Inflator Body That Cracked During Forming Of The Curl That Retains The Igniter Plug In The End Of The Inflator. Also The Igniter End Cap Can Separate

1995 Ford Probe Air Bags,frontal Recall | Feb 24, 1995

The Passenger Side Air Bag Has An Inflator Body That Cracked During Forming Of The Curl That Retains The Igniter Plug In The End Of The Inflator. Also The Igniter End Cap Can Separate From The Inflator.the Passenger Side Air Bag May Not Inflate Properly Resulting In Reduced Occupant Protection In A Vehicle Accident. If The Igniter End Cap Separates In A Frontal Collision, Hot Gases Can Be Released And Ignite Flammable Material Or Cause Burn Injuries.. Follwoing Is The Summary Of Corrective Actions Taken: Dealers Will Remove And Replace The Passenger Side Air Bag Module.
system: Interior; Passive Restraints; Air Bag; Passenger. Vehicle Description: Passenger Side Air Bag In Passenger Cars, Vans Andmulti-purpose Vehicles. Note: If Your Vehicle Is Presented To An Authorized Dealer On An Agreed Upon Service Date And The Remedy Is Not Provided Free Of Charge Within A Reasonable Time, Contact Ford At 1-800-392-3673. Also Contact The National Highway Traffic Safety Administration’s Auto Safety Hotline At 1-800-424-9393.

This recall was issued on Feb 24, 1995 for 1995 Ford Probe, manufactured by FORD MOTOR COMPANY, in response to Air Bags,frontal problems.

1995 Ford Mustang Recall | The Passenger Side Air Bag Has An Inflator Body That Cracked During Forming Of The Curl That Retains The Igniter Plug In The End Of The Inflator. Also The Igniter End Cap Can Separate

1995 Ford Mustang Air Bags,frontal Recall | Feb 24, 1995

The Passenger Side Air Bag Has An Inflator Body That Cracked During Forming Of The Curl That Retains The Igniter Plug In The End Of The Inflator. Also The Igniter End Cap Can Separate From The Inflator.the Passenger Side Air Bag May Not Inflate Properly Resulting In Reduced Occupant Protection In A Vehicle Accident. If The Igniter End Cap Separates In A Frontal Collision, Hot Gases Can Be Released And Ignite Flammable Material Or Cause Burn Injuries.. Follwoing Is The Summary Of Corrective Actions Taken: Dealers Will Remove And Replace The Passenger Side Air Bag Module.
system: Interior; Passive Restraints; Air Bag; Passenger. Vehicle Description: Passenger Side Air Bag In Passenger Cars, Vans Andmulti-purpose Vehicles. Note: If Your Vehicle Is Presented To An Authorized Dealer On An Agreed Upon Service Date And The Remedy Is Not Provided Free Of Charge Within A Reasonable Time, Contact Ford At 1-800-392-3673. Also Contact The National Highway Traffic Safety Administration’s Auto Safety Hotline At 1-800-424-9393.

This recall was issued on Feb 24, 1995 for 1995 Ford Mustang, manufactured by FORD MOTOR COMPANY, in response to Air Bags,frontal problems.

1995 Ford Crown Victoria Recall | The Passenger Side Air Bag Has An Inflator Body That Cracked During Forming Of The Curl That Retains The Igniter Plug In The End Of The Inflator. Also The Igniter End Cap Can Separate

1995 Ford Crown Victoria Air Bags,frontal Recall | Feb 24, 1995

The Passenger Side Air Bag Has An Inflator Body That Cracked During Forming Of The Curl That Retains The Igniter Plug In The End Of The Inflator. Also The Igniter End Cap Can Separate From The Inflator.the Passenger Side Air Bag May Not Inflate Properly Resulting In Reduced Occupant Protection In A Vehicle Accident. If The Igniter End Cap Separates In A Frontal Collision, Hot Gases Can Be Released And Ignite Flammable Material Or Cause Burn Injuries.. Follwoing Is The Summary Of Corrective Actions Taken: Dealers Will Remove And Replace The Passenger Side Air Bag Module.
system: Interior; Passive Restraints; Air Bag; Passenger. Vehicle Description: Passenger Side Air Bag In Passenger Cars, Vans Andmulti-purpose Vehicles. Note: If Your Vehicle Is Presented To An Authorized Dealer On An Agreed Upon Service Date And The Remedy Is Not Provided Free Of Charge Within A Reasonable Time, Contact Ford At 1-800-392-3673. Also Contact The National Highway Traffic Safety Administration’s Auto Safety Hotline At 1-800-424-9393.

This recall was issued on Feb 24, 1995 for 1995 Ford Crown Victoria, manufactured by FORD MOTOR COMPANY, in response to Air Bags,frontal problems.

1995 Ford Windstar Recall | The Passenger Side Air Bag Has An Inflator Body That Cracked During Forming Of The Curl That Retains The Igniter Plug In The End Of The Inflator. Also The Igniter End Cap Can Separate

1995 Ford Windstar Air Bags,frontal Recall | Feb 24, 1995

The Passenger Side Air Bag Has An Inflator Body That Cracked During Forming Of The Curl That Retains The Igniter Plug In The End Of The Inflator. Also The Igniter End Cap Can Separate From The Inflator.the Passenger Side Air Bag May Not Inflate Properly Resulting In Reduced Occupant Protection In A Vehicle Accident. If The Igniter End Cap Separates In A Frontal Collision, Hot Gases Can Be Released And Ignite Flammable Material Or Cause Burn Injuries.. Follwoing Is The Summary Of Corrective Actions Taken: Dealers Will Remove And Replace The Passenger Side Air Bag Module.
system: Interior; Passive Restraints; Air Bag; Passenger. Vehicle Description: Passenger Side Air Bag In Passenger Cars, Vans Andmulti-purpose Vehicles. Note: If Your Vehicle Is Presented To An Authorized Dealer On An Agreed Upon Service Date And The Remedy Is Not Provided Free Of Charge Within A Reasonable Time, Contact Ford At 1-800-392-3673. Also Contact The National Highway Traffic Safety Administration’s Auto Safety Hotline At 1-800-424-9393.

This recall was issued on Feb 24, 1995 for 1995 Ford Windstar, manufactured by FORD MOTOR COMPANY, in response to Air Bags,frontal problems.

1995 Ford Contour Recall | The Passenger Side Air Bag Has An Inflator Body That Cracked During Forming Of The Curl That Retains The Igniter Plug In The End Of The Inflator. Also The Igniter End Cap Can Separate

1995 Ford Contour Air Bags,frontal Recall | Feb 24, 1995

The Passenger Side Air Bag Has An Inflator Body That Cracked During Forming Of The Curl That Retains The Igniter Plug In The End Of The Inflator. Also The Igniter End Cap Can Separate From The Inflator.the Passenger Side Air Bag May Not Inflate Properly Resulting In Reduced Occupant Protection In A Vehicle Accident. If The Igniter End Cap Separates In A Frontal Collision, Hot Gases Can Be Released And Ignite Flammable Material Or Cause Burn Injuries.. Follwoing Is The Summary Of Corrective Actions Taken: Dealers Will Remove And Replace The Passenger Side Air Bag Module.
system: Interior; Passive Restraints; Air Bag; Passenger. Vehicle Description: Passenger Side Air Bag In Passenger Cars, Vans Andmulti-purpose Vehicles. Note: If Your Vehicle Is Presented To An Authorized Dealer On An Agreed Upon Service Date And The Remedy Is Not Provided Free Of Charge Within A Reasonable Time, Contact Ford At 1-800-392-3673. Also Contact The National Highway Traffic Safety Administration’s Auto Safety Hotline At 1-800-424-9393.

This recall was issued on Feb 24, 1995 for 1995 Ford Contour, manufactured by FORD MOTOR COMPANY, in response to Air Bags,frontal problems.

1995 Ford Ll9000 Recall | A Connector In The Wiring Where The Tilt Hood Mounted Lamps Attach To The Vehicle Wiring Harness Was Built Without Sealing Plugs. Moisture, Road Salt Or Other Contaminants Can Enter The Connection Resulting

1995 Ford Ll9000 Electrical System,wiring Recall | May 09, 1995

A Connector In The Wiring Where The Tilt Hood Mounted Lamps Attach To The Vehicle Wiring Harness Was Built Without Sealing Plugs. Moisture, Road Salt Or Other Contaminants Can Enter The Connection Resulting In Crossed Circuits, Shorts Or Corrosion Of The Wiring Of The Connector.the Headlamps Or Other Front-end Lighting Systems Can Malfunction As A Result Of This Condition Increasing The Potential For A Vehicle Accident.. Follwoing Is The Summary Of Corrective Actions Taken: Dealers Will Inspect The Connector And Install Sealing Plugs In The Open Cavities. If The Inspection Reveals Corrosion, A New Connector Will Be Installed.
system: Electrical; Wiring; Other Part.vehicle Description: Light And Medium Duty Trucks, Chassis-cabs And Cowl-chassis.note: If Your Vehicle Is Presented To An Authorized Dealer On An Agreed Up0n Service Date And The Remedy Is Not Provided Free Of Charge Within A Reasonable Time, Please Contact Ford At 1-800-392-3673. Also Contact The National Highway Traffic Safety Administration’s Auto Safety Hotline At 1-800-424-9393.

This recall was issued on May 09, 1995 for 1995 Ford Ll9000, manufactured by FORD MOTOR COMPANY, in response to Electrical System,wiring problems.

1995 Ford B700 Recall | A Connector In The Wiring Where The Tilt Hood Mounted Lamps Attach To The Vehicle Wiring Harness Was Built Without Sealing Plugs. Moisture, Road Salt Or Other Contaminants Can Enter The Connection Resulting

1995 Ford B700 Electrical System,wiring Recall | May 09, 1995

A Connector In The Wiring Where The Tilt Hood Mounted Lamps Attach To The Vehicle Wiring Harness Was Built Without Sealing Plugs. Moisture, Road Salt Or Other Contaminants Can Enter The Connection Resulting In Crossed Circuits, Shorts Or Corrosion Of The Wiring Of The Connector.the Headlamps Or Other Front-end Lighting Systems Can Malfunction As A Result Of This Condition Increasing The Potential For A Vehicle Accident.. Follwoing Is The Summary Of Corrective Actions Taken: Dealers Will Inspect The Connector And Install Sealing Plugs In The Open Cavities. If The Inspection Reveals Corrosion, A New Connector Will Be Installed.
system: Electrical; Wiring; Other Part.vehicle Description: Light And Medium Duty Trucks, Chassis-cabs And Cowl-chassis.note: If Your Vehicle Is Presented To An Authorized Dealer On An Agreed Up0n Service Date And The Remedy Is Not Provided Free Of Charge Within A Reasonable Time, Please Contact Ford At 1-800-392-3673. Also Contact The National Highway Traffic Safety Administration’s Auto Safety Hotline At 1-800-424-9393.

This recall was issued on May 09, 1995 for 1995 Ford B700, manufactured by FORD MOTOR COMPANY, in response to Electrical System,wiring problems.