2007 Ford F800 Recall | Certain Federal-mogul Aftermarket Fuel Pumps Sold Under The Brand Names Of Carter,

2007 Ford F800 Fuel System, Gasoline,delivery,fuel Pump Recall | Aug 27, 2007

Certain Federal-mogul Aftermarket Fuel Pumps Sold Under The Brand Names Of Carter, Accuflow, Napa, Truflow, Parts Depo, And Parts Master, Shipped Between August 2006 And July 2007 For Use On The Vehicles Listed Above. The Fuel Pump Diaphragm In Certain Production Runs May Have Been Improperly Installed Or Inadequately Tested Which May Cause The Fuel Pump To Leak.

A Leaking Fuel Pump Could Create A Vehicle Fire Hazard.

Summary Of Corrective Actions Taken: Federal-mogul Will Notify Owners And Replace The Defective Fuel Pumps Free Of Charge. The Recall Began On October 15, 2007. Owners Can Contact Federal-mogul At 248-354-7700.

This Recall Only Pertains To Aftermarket Carter, Napa, Accuflow, Tru Flow, Parts Master, And Parts Depot Brand Fuel Pumps And Has No Relation To Any Original Equipment Installed On The Listed Motor Vehicles.customers May Contact The National Highway Traffic Safety Administration’s Vehicle Safety Hotline At 1-888-327-4236 (tty: 1-800-424-9153); Or Go To Http://www.safercar.gov.

This recall was issued on Aug 27, 2007 for 2007 Ford F800, manufactured by FEDERAL-MOGUL CORPORATION, in response to Fuel System, Gasoline,delivery,fuel Pump problems.

1981 Ford F800 Recall | The Involved Vehicles Were Assembled With The Left Front Brake Tube Retaining Clip Missing. The Absence Of A Retaining Clip May Allow The Brake Tube To Rub Against The Shock Absorber, Causing Wear

1981 Ford F800 Service Brakes, Hydraulic,foundation Components,hoses, Lines/piping, And Fittings Recall | July 17, 1981

The Involved Vehicles Were Assembled With The Left Front Brake Tube Retaining Clip Missing. The Absence Of A Retaining Clip May Allow The Brake Tube To Rub Against The Shock Absorber, Causing Wear On The Tube And, Eventually, Loss Of Brake Fluid.. Follwoing Is The Summary Of Corrective Actions Taken: Missing Brake Tube Clips Will Be Installed And Any Chafed Brake Tubes Will Be Replaced.
vehicle Description: School Buses And Trucks Equipped With 8.2 Liter Dieselengines And Hydraulic Brakes.system: Service Brakes; Left Hand Front Brake Tube Retaining Clip.consequences Of Defect: On Vehicles Equipped With Single System Hydraulicbrakes, Sufficient Loss Of Brake Fluid Could Result In Loss Of Service Brakingcapability. This Could Cause A Loss Of Vehicle Control And An Accident. Onvehicles Equipped With Split System Hydraulic Brakes, Loss Of Brake Fluid Inthe Hydraulic Circuit Of One System Could Cause Loss Of Service Braking In Theaffected System. Braking Distance Would Be Increased, Possibly Resulting In Anaccident.

This recall was issued on July 17, 1981 for 1981 Ford F800, manufactured by FORD MOTOR COMPANY, in response to Service Brakes, Hydraulic,foundation Components,hoses, Lines/piping, And Fittings problems.

1983 Ford F800 Recall | On The Affected Vehicles, The Wiring Assembly To The Floor Mounted Headlamp Dimmer Switch May Be Too Tight; Should Wires Disconnect, The Headlights Will Not Operate.

1983 Ford F800 Electrical System,wiring Recall | Feb 15, 1983

On The Affected Vehicles, The Wiring Assembly To The Floor Mounted Headlamp Dimmer Switch May Be Too Tight; Should Wires Disconnect, The Headlights Will Not Operate.. Follwoing Is The Summary Of Corrective Actions Taken: The Dealer Will Modify The Dimmer Switch Wiring With A Wire Extension Assembly At No Charge To Owner.
vehicle Description: Medium Trucks, Heavy Trucks And Bus Chassis.system: Lighting And Communications; Headlamp Dimmer Switch Wiring Harness.consequences Of Defect: Driver Foot Pressure On Or Above The Dimmer Switch Mayresult In Disconnection Of The Wires And Subsequent Loss Of Headlampillumination. Headlamp Failure Could Cause A Vehicle Crash.

This recall was issued on Feb 15, 1983 for 1983 Ford F800, manufactured by FORD MOTOR COMPANY, in response to Electrical System,wiring problems.

1981 Ford F800 Recall | The Primary Circuit Connection, Which Provides Primary Electrical Power To The Engine, Could Deteriorate Due To High Current Draw Produced By Builder-installed Equipment.

1981 Ford F800 Electrical System,wiring Recall | June 15, 1981

The Primary Circuit Connection, Which Provides Primary Electrical Power To The Engine, Could Deteriorate Due To High Current Draw Produced By Builder-installed Equipment.. Follwoing Is The Summary Of Corrective Actions Taken: The Main Cab Wiring Harness Electrical Connector Will Be Modified To Eliminate Deterioration At No Charge To Owner.
vehicle Description: School Buses.system: Electrical; Primary Circuit Connector.consequences Of Defect: Depending On The Degree Of Deterioration Present,intermittent Or Complete Loss Of All Vehicle Electrical Power Could Result.this Would Cause The Engine To Stop Running And Power Steering Assist And Powerassist For Hydraulic Brakes Would Be Lost, If The Vehicle Is So Equipped. Thesefailures Could Occur Without Warning, Possibly Resulting In An Accident.note: Vehicle Should Be Removed From Service Until The Problem Is Corrected.

This recall was issued on June 15, 1981 for 1981 Ford F800, manufactured by FORD MOTOR COMPANY, in response to Electrical System,wiring problems.

1979 Ford F800 Recall | The Air Brake Lines May Be Routed Too Close To The Exhaust Muffler. Because The Air Brake Lines Are Made Of Nylon Material, Heat From The Exhaust Muffler Can Weaken The Brake Line

1979 Ford F800 Service Brakes, Air,supply,hoses, Lines/piping, And Fittings Recall | Feb 22, 1979

The Air Brake Lines May Be Routed Too Close To The Exhaust Muffler. Because The Air Brake Lines Are Made Of Nylon Material, Heat From The Exhaust Muffler Can Weaken The Brake Line Tubes, Possibly Causing Them To Rupture. Tube Rupture Could Result In Loss Of Air In The Secondary Air Brake System.. Follwoing Is The Summary Of Corrective Actions Taken: New Nylon Air Brake Tubes Will Be Installed And Rerouted Without Charge To Owner.
vehicle Description: Trucks And Buses Equipped With Gasoline Engines And Airbrakes.system: Service Brakes; Air Brake Tubes.consequences Of Defect: Partial Loss Of Vehicle Service Brakes Can Result Andthe Rear Spring Brakes Could Activate, Possibly Resulting In A Vehicleaccident.note: Rupture Of The Tubes For The Secondary System Can Be Detected By Acontinuous Buzzer And Warning Light, Signaling Low Air Pressure, And By Thedual Reading Air Gauge Indicator. Vehicle Operator Is Cautioned To Avoidperiods Of Engine Idling, Particularly When The Choke And Throttle Are Set.this Condition Generates Substantial Heat, Which Can Cause Tube Rupture.

This recall was issued on Feb 22, 1979 for 1979 Ford F800, manufactured by FORD MOTOR COMPANY, in response to Service Brakes, Air,supply,hoses, Lines/piping, And Fittings problems.

1984 Ford F800 Recall | Two-inch Spacers Specified For Installation Between The Front Axles And Each Front Spring Assembly Were Omitted During Manufacture. Under Certain Turning And Bouncing Conditions, A Front Tire Could Contact Adjacent Vehicle Components,

1984 Ford F800 Suspension,front,springs,coil Springs Recall | Apr 10, 1984

Two-inch Spacers Specified For Installation Between The Front Axles And Each Front Spring Assembly Were Omitted During Manufacture. Under Certain Turning And Bouncing Conditions, A Front Tire Could Contact Adjacent Vehicle Components, Resulting In A Possible Separation Of The Drag Link To Steering Arm Balljoint Or Loss Of Tire Pressure.. Follwoing Is The Summary Of Corrective Actions Taken: Front Axle Spacers Will Be Installed Without Charge.
vehicle Description: Heavy Trucks Equipped With 9,500 Or 12,000 Pound Frontaxles And Single Rear Axles.system: Suspension; Front Axle Spacers.consequences Of Defect: Both Conditions Can Cause A Loss Of Steering Controlwith The Potential For An Accident.note: Front Wheels Should Be Inspected For Indications Of Damage Fromcontacting The Fenders Or Steering Linkage. Do Not Drive On Tires That Havecuts Penetrating The Tire Carcass.

This recall was issued on Apr 10, 1984 for 1984 Ford F800, manufactured by FORD MOTOR COMPANY, in response to Suspension,front,springs,coil Springs problems.

1981 Ford F800 Recall | The Master Cylinder To Chasis Brake Tube And Hose Assemblies May Have Been Moved From Their Intended Position, Which Could Allow Chafing Against Underbody Components. Chafing Promotes Wear Of The Brake Tube And

1981 Ford F800 Service Brakes, Hydraulic,foundation Components,hoses, Lines/piping, And Fittings Recall | Oct 15, 1981

The Master Cylinder To Chasis Brake Tube And Hose Assemblies May Have Been Moved From Their Intended Position, Which Could Allow Chafing Against Underbody Components. Chafing Promotes Wear Of The Brake Tube And Hose Assembly And Could Cause A Loss Of Brake Fluid.. Follwoing Is The Summary Of Corrective Actions Taken: Upon Inspection Brake Tube Clips Will Be Installed, If Necessary, And Brake Tubes And Hose Assemblies Will Be Replaced Or Rerouted.
vehicle Description: School Buses Equipped With Hydraulic Brakes.system: Service Brakes; Brake Tube And Hose Assembly.consequences Of Defect: On Models With Standard Split System Hydraulic Brakes,loss Of Brake Fluid Could Cause Loss Of Vehicle Braking In The Affected System.a Portion Of The Brake System Would Remain Functional But Vehicle Stoppingdistance Would Be Significantly Increased And An Accident Could Result. Formodels With Single System Hydraulic Brakes, A Sufficient Loss Of Brake Fluidcould Result In Loss Of Service Brakes, Loss Of Vehicle Control, And Anaccident.note: In Both Single And Split Braking Systems, The Vehicle Operator May Noticea Drop In Brake Pedal Height During Application In The Early Stages Of Brakeline Failure. On Split System Hydraulic Brakes, Loss Of Brake Fluid In One Partof The System May Be Detected By Illumination Of The Brake Warning Lamp.vehicle Should Not Be Driven If Warning Light Is Activated Or Visible Chafingof The Brake Tube Or Hose Assembly Exists, Until The Problem Is Corrected.

This recall was issued on Oct 15, 1981 for 1981 Ford F800, manufactured by FORD MOTOR COMPANY, in response to Service Brakes, Hydraulic,foundation Components,hoses, Lines/piping, And Fittings problems.

1995 Ford F800 Recall | The Hand Throttle Cable Can Wear The Brass Swivel Block On The Governor Lever Through Which It Passes.

1995 Ford F800 Vehicle Speed Control Recall | Aug 02, 1995

The Hand Throttle Cable Can Wear The Brass Swivel Block On The Governor Lever Through Which It Passes.this Wear Can Result In The Governor Jamming In Thedamaged Swivel And Could Prevent The Governor Lever From Returning To The Idle Position.. Follwoing Is The Summary Of Corrective Actions Taken: Dealers Will Install A Revised Governor Lever With A Stainless Steel Swivel. Also Letters Will Be Sent To Vehicle Owners That Have The Same Vehicles But Do Not Have A Ford Installed Hand Throttle Advising Them That They May Require Service If They Have Had An After Market Hand Throttle Installed.
system: Fuel; Throttle Linkages And Control.vehicle Description: Trucks, Chassis-cabs And Cowl-chassis Vehicles With Inline Fuel Injection Pump Equipped Fd-1060 Or Fd-1460 Engines And Hand Throttles.note: The Vehicle Brakes Are Capable Of Overriding The Engine Power And Bringing The Vehicle To A Stop.note: Owners Who Take Their Vehicles To An Authorized Dealer On An Agreed Upon Service Date And Do Not Receive The Free Remedy Within A Reasonablet Ime, Should Contact Ford At 1-800-392-3673. Also Contact The National Highway Traffic Safety Administration’s Auto Safety Hotline At 1-800-424-9393.

This recall was issued on Aug 02, 1995 for 1995 Ford F800, manufactured by FORD MOTOR COMPANY, in response to Vehicle Speed Control problems.

1984 Ford F800 Recall | The Involved Vehicles Were Produced With Hydraulic Brake Booster Supply Hoses That Are Located Too Close To The Engine Exhaust Manifold And May Chafe And Develop Heat Damage During Vehicle Operation. Chafing And Heat

1984 Ford F800 Service Brakes, Hydraulic,power Assist,vacuum,hoses, Lines/piping, And Fittings Recall | Oct 23, 1984

The Involved Vehicles Were Produced With Hydraulic Brake Booster Supply Hoses That Are Located Too Close To The Engine Exhaust Manifold And May Chafe And Develop Heat Damage During Vehicle Operation. Chafing And Heat Induced Deterioration Of A Hose Due To Direct Contact With The Manifold May Cause The Hose To Wear. A Subsequent Rupture Will Result In Pump Fluid Loss.. Follwoing Is The Summary Of Corrective Actions Taken: The Dealer Will Relocate And Replace The Brake Booster Supply Tube And Hose As Necessary At No Cost To Owner.
vehicle Description: Trucks And Buses Equipped With Hydraulic Brakes Andgasoline And Propane Engines.system: Service Brakes; Booster Supply Hose.consequences Of Defect: Should This Deterioration And Rupture Occur Duringvehicle Operation, Distance Required For Stopping Will Be Increased, Possiblyresulting In An Accident. Leaking Fluid May Also Ignite, Resulting In An Enginecompartment Fire And Possible Personal Injury.

This recall was issued on Oct 23, 1984 for 1984 Ford F800, manufactured by FORD MOTOR COMPANY, in response to Service Brakes, Hydraulic,power Assist,vacuum,hoses, Lines/piping, And Fittings problems.

1992 Ford F800 Recall | Water Can Enter The Door Latch Release Cable. If The Vehicle Is Operated In Below Freezing Temperatures, The Water In The Door Latch Release Cable Can Freeze And Cause The Latch Mechanism To

1992 Ford F800 Structure,body,door Recall | Jan 14, 1992

Water Can Enter The Door Latch Release Cable. If The Vehicle Is Operated In Below Freezing Temperatures, The Water In The Door Latch Release Cable Can Freeze And Cause The Latch Mechanism To Malfunction.the Malfunction Of The Door Latch Release Can Result Inthree Different Problems: 1) The Door Will Not Be Able To Be Relatched, 2) Theinside Door Handle Can Become Inoperative, And 3) The Door Could Appear To Belatched When It Is Not, Allowing The Door To Open Unexpectedly If It Is Jarred,and Increasing The Risk Of Injury To The Adjacent Seat Occupant.. Follwoing Is The Summary Of Corrective Actions Taken: Revised Door Release Cables And Water Shields Will Be Installed.
system: Structure; Door Latch.vehicle Description: Multi-purpose Vehicles, Light Trucks And Medium Trucks.

This recall was issued on Jan 14, 1992 for 1992 Ford F800, manufactured by FORD MOTOR COMPANY, in response to Structure,body,door problems.