2000 Ford Heavy Duty Recall | Vehicle Description: Motor Home Chassis And Heavy Duty Trucks. The Affected

2000 Ford Heavy Duty Steering,linkages,tie Rod Assembly Recall | Nov 28, 2000

Vehicle Description: Motor Home Chassis And Heavy Duty Trucks. The Affected Vehicles Have Tie Rod Ends And/or Drag Link Assembly Ends That Could Have Insufficient Harness In The Ball Stud.

This Could Result In Premature Wear And, Potentially, Separation Of The Ball Stud From Its Socket.

Summary Of Corrective Actions Taken: Dealers Will Replace The Tie Rod Ends And/or Drag Link Assemblies. Owner Notification Began December 27, 2000.owners Who Take Their Vehicles To An Authorized Dealer On An Agreed Upon Service Date And Do Not Receive The Free Remedy Within A Reasonable Time Should Contact Ford At 1-800-392-3673.

Also Contact The National Highway Traffic Safety Administration’s Auto Safety Hotline At 1-888-dash-2-dot (1-888-327-4236).

This recall was issued on Nov 28, 2000 for 2000 Ford Heavy Duty, manufactured by FORD MOTOR COMPANY, in response to Steering,linkages,tie Rod Assembly problems.

1967 Ford Ford Recall |

1967 Ford Ford Equipment,mechanical,jacks Recall | May 10, 1967

. Follwoing Is The Summary Of Corrective Actions Taken:
possible That The Sharp End Of The Jack Handle Could Deform A Stop In The Rachet Assembly And Sub- Sequently Interfere With The Pawl.this Could Cause Failure After The Jack Had Been Used A Few Times.(replace Jack Column And Case Assembly.)

This recall was issued on May 10, 1967 for 1967 Ford Ford, manufactured by FORD MOTOR COMPANY, in response to Equipment,mechanical,jacks problems.

1977 Ford Club Wagon Recall | On The Involved Vehicles, The Steering Tie Rod And Link Assemblies With Adjusting Sleeve Clamps May Have Been Improperly Manufactured. The Clamps Contain A Sharp Die Mark Which Could Cause The Clamp To

1977 Ford Club Wagon Steering,linkages,tie Rod Assembly Recall | Oct 25, 1977

On The Involved Vehicles, The Steering Tie Rod And Link Assemblies With Adjusting Sleeve Clamps May Have Been Improperly Manufactured. The Clamps Contain A Sharp Die Mark Which Could Cause The Clamp To Fracture When The Clamp Bolt Is Tightened To Specifications. The Clamp Could Break And Cause Separation Of The Tie Rod Adjusting Sleeves.. Follwoing Is The Summary Of Corrective Actions Taken: The Dealer Will Replace The Steering Tie Rod Adjusting Sleeve And Clamp Assembly, Free Of Charge, On All Affected Vehicles.
vehicle Description: Light Trucks.system: Steering; Tie Rod Adjusting Sleeve Clamps.consequences Of Defect: Should Separation Occur, Loss Of Steering Control Andan Accident Could Occur Without Prior Warning.

This recall was issued on Oct 25, 1977 for 1977 Ford Club Wagon, manufactured by FORD MOTOR COMPANY, in response to Steering,linkages,tie Rod Assembly problems.

1977 Ford E350 Recall | On The Involved Vehicles, The Steering Tie Rod And Link Assemblies With Adjusting Sleeve Clamps May Have Been Improperly Manufactured. The Clamps Contain A Sharp Die Mark Which Could Cause The Clamp To

1977 Ford E350 Steering,linkages,tie Rod Assembly Recall | Oct 25, 1977

On The Involved Vehicles, The Steering Tie Rod And Link Assemblies With Adjusting Sleeve Clamps May Have Been Improperly Manufactured. The Clamps Contain A Sharp Die Mark Which Could Cause The Clamp To Fracture When The Clamp Bolt Is Tightened To Specifications. The Clamp Could Break And Cause Separation Of The Tie Rod Adjusting Sleeves.. Follwoing Is The Summary Of Corrective Actions Taken: The Dealer Will Replace The Steering Tie Rod Adjusting Sleeve And Clamp Assembly, Free Of Charge, On All Affected Vehicles.
vehicle Description: Light Trucks.system: Steering; Tie Rod Adjusting Sleeve Clamps.consequences Of Defect: Should Separation Occur, Loss Of Steering Control Andan Accident Could Occur Without Prior Warning.

This recall was issued on Oct 25, 1977 for 1977 Ford E350, manufactured by FORD MOTOR COMPANY, in response to Steering,linkages,tie Rod Assembly problems.

1977 Ford E250 Recall | On The Involved Vehicles, The Steering Tie Rod And Link Assemblies With Adjusting Sleeve Clamps May Have Been Improperly Manufactured. The Clamps Contain A Sharp Die Mark Which Could Cause The Clamp To

1977 Ford E250 Steering,linkages,tie Rod Assembly Recall | Oct 25, 1977

On The Involved Vehicles, The Steering Tie Rod And Link Assemblies With Adjusting Sleeve Clamps May Have Been Improperly Manufactured. The Clamps Contain A Sharp Die Mark Which Could Cause The Clamp To Fracture When The Clamp Bolt Is Tightened To Specifications. The Clamp Could Break And Cause Separation Of The Tie Rod Adjusting Sleeves.. Follwoing Is The Summary Of Corrective Actions Taken: The Dealer Will Replace The Steering Tie Rod Adjusting Sleeve And Clamp Assembly, Free Of Charge, On All Affected Vehicles.
vehicle Description: Light Trucks.system: Steering; Tie Rod Adjusting Sleeve Clamps.consequences Of Defect: Should Separation Occur, Loss Of Steering Control Andan Accident Could Occur Without Prior Warning.

This recall was issued on Oct 25, 1977 for 1977 Ford E250, manufactured by FORD MOTOR COMPANY, in response to Steering,linkages,tie Rod Assembly problems.

1995 Ford Mustang Recall | The Affected Vehicles Were Built With Outer Tie Rod Ends With Incorrect Taper Ball Studs. The Incorrect Tapered Ball Studs Can Fracture Within 50,000 Miles.

1995 Ford Mustang Steering,linkages,tie Rod Assembly Recall | July 17, 1995

The Affected Vehicles Were Built With Outer Tie Rod Ends With Incorrect Taper Ball Studs. The Incorrect Tapered Ball Studs Can Fracture Within 50,000 Miles.a Fractured Ball Stud Can Result In A Noticeable Shake Or Shimmy And Could Cause The Affected Wheel To Tuck Inward Or Outward, Increasing The Potential For A Vehicle Accident.. Follwoing Is The Summary Of Corrective Actions Taken: Dealers Will Inspect The Outer Tie Rod Ends And Replace The Incorrectly Tapered Ball Studs.
system: Steering; Linkages; Tie Rod; End.vehicle Description: Passenger Vehicles.note: Owners Who Take Their Vehicles To An Authorized Dealer On An Agreed Upon Service Date And Do Not Receive The Free Remedy Within A Reasonable Time, Should Contact Ford At 1-800-392-3673. Also Contact The National Highway Traffic Safety Administration’s Auto Safety Hotline At 1-800-424-9393.

This recall was issued on July 17, 1995 for 1995 Ford Mustang, manufactured by FORD MOTOR COMPANY, in response to Steering,linkages,tie Rod Assembly problems.

1995 Ford Explorer Recall | The Inner Tie Rod Assemblies Were Improperly Manufactured And Can Fracture Causing Shaking Or Shimmy At Low Speeds.

1995 Ford Explorer Steering,linkages,tie Rod Assembly Recall | Mar 15, 1995

The Inner Tie Rod Assemblies Were Improperly Manufactured And Can Fracture Causing Shaking Or Shimmy At Low Speeds.this Condition Can Cause The Wheel On The Side With The Broken Tie Rod To Tuck Inward Or Outward And Slide Resulting In An Increased Potential For A Vehicle Accident.. Follwoing Is The Summary Of Corrective Actions Taken: Dealers Will Inspect The Inner Tie Rods And Replace The Suspect Tie Rods.
system: Steering; Linkages; Tie Rod; Inner.vehicle Description: Multi-purpose Passenger Vehicles.note: If Your Vehicle Is Presented To An Authorized Dealer On An Agreed Upon Service Date And The Remedy Is Not Provided Free Of Charge Within A Reasonable Time, Please Contact Ford At 1-800-392-3673. Also Contact The National Highway Traffic Safety Administration’s Auto Safety Hotline At 1-800-424-9393.

This recall was issued on Mar 15, 1995 for 1995 Ford Explorer, manufactured by FORD MOTOR COMPANY, in response to Steering,linkages,tie Rod Assembly problems.

Notice: ob_end_flush(): failed to send buffer of zlib output compression (0) in /home/veinly/public_html/fordproblem.com/wp-includes/functions.php on line 3092